Характеристики продукта
● Отсутствие движущихся частей
● Быстрая скорость переключения
● Чрезвычайно стабильный режим фиксации
● Низкое энергопотребление
● Превосходная стабильность и надежность
Области применения
● Пассивные оптические сети
● Системы оптической защиты
● Измерительные системы
● Мониторинг сетей
Технические характеристики
| Parameters | unit | FT-98-UMS-2×2 | unit | |
| Unidirectional | Bidirectional | |||
| Wavelength Range(波长范围) | nm | 1525 ~ 1565 | Other band optional | |
| Insertion Loss（插入损耗） | dB | 0.7(Typ.);1.1(Max) | 0.8(Typ.);1.2(Max) | |
| PDL（偏振相关损耗） | dB | 0.10(Typ.);0.20(Max) | 0.10(Typ.),0.30(Max) | |
| Return Loss（ 回波损耗） | dB | 45 | 30 | |
| Crosstalk（ 串扰） | dB | 40 | 30 | |
| Repeatability（重复性） | dB | +/- 0.01 | ||
| Durability（使用寿命） | Cycles | > 100 Billions | ||
| Switching Speed（切换速度） | s | Regular (50~200); Ultra-fast (5~20) | ||
| Maximum Optical Power（功率） | mW | 500 | ||
| Storage Temperature（存储温度） | °C | -40 ~ 85 | ||
| Operating Temperature（工作温度 ） | ℃ | -5 ~ 70 | ||
| Dimension( L ×W × H )（尺寸 ） | mm | 63 × 8 × 7 | ||
Параметры электронного управления
| Parameter | Specification | Unit | |
| Regular | Ultra-fast | ||
| Switching Speed | 50~200 | 5~20 | μs |
| Switching Voltage(VCC) | 3( +/-5%) | 5.0~6.0 | V |
| Switching Current | < 200 | < 500 | mA |
| Pulse Width(typical) | 1000 | 20 | μs |
| Claim Frequency | < 800 | < 3000 | Hz |
Определение выводов драйвера
Одност
| Switching State | Pin1 | Pin2 | The Optical Output Port |
| State “0” | 1(Voltage = VCC) | 0(Voltage = | IN1→OUT 1; IN2→OUT 2 |
| GND) | |||
| State “ 1” | 0(Voltage = GND) | 1(Voltage =VCC) | IN1→OUT 2; IN2→OUT 1 |
Двуст
| Switching State | Pin1 | Pin2 | The Optical Output Port |
| State “0” | 1(Voltage = VCC) | 0(Voltage =GND) | IN1↔OUT 1; IN2↔OUT 2 |
| State “ 1” | 0(Voltage = GND) | 1(Voltage =VCC) | IN1↔OUT 2; IN2↔OUT 1 |
Габаритные размеры (мм)
Информация для заказа FT-98－UMS-2×2-A-B-C-D-E-F-G
| A | B | C | D | E | F |
| Working Mode | SwitchingSpeed | Operating Wavelength | Fiber Tuber | Fiber Length | Connector Type |
| 1.Regular2. Bidirectional | 1.50~200us 2.5~20us3. Others | 1.C Band1525~1565 nm2. L Band 1565-1615 nm3. C & L Band4. Others | 1.250μm fiber 2. 900μmfiber3. Others | 1.0.5 +/- 0.1 m2. 1.0 +/- 0.1 m3. Others | 0.No Connector1. FC/UPC2. FC/APC3. SC/UPC4. SC/APC5. LC/PC6. MU/PC7. Others |
Важное уведомление:
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they are applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or other. Further details are available from any F-tone Networks sales representative.
Power and Wavelength Testing
Test the signal delivering strength and wavelength, to ensure the signal decoding capacity of the receiver, and the wavelength remains consistent from the transmitter to the receiver.
Traffic Testing
Test the bit error rate and packet loss rate, to make them meet the corresponding standards and ensure the performance of transceivers.
Optical Performance Testing
Test the transceivers’ eye diagram situation, receiving sensitivity, extinction ratio, wavelength, light-emitting, light-receiving, current and voltage, to ensure the signal quality, stability and reliability of the transmission.
End Face Testing
Check the end face of the transceivers and keep them clean for more stable data transmission, better performance, and durability.
