Характеристики
● Корпус SOP с 4-контактным разъёмом в миниатюрном исполнении (4,4 × 4,3 × 2,1 мм / 0,173 × 0,169 × 0,083 дюйма)
● Низкие требования к мощности управляющего сигнала (совместимость с TTL/CMOS)
● Отсутствие движущихся частей
● Высокая надёжность
● Отсутствие дугового разряда и гасительных цепей
● Изоляция входа/выхода 1500 Врмс
● Доступна версия в катушке
Области применения
● Телекоммуникации (ПК, электронные блокноты)
● Измерительное и испытательное оборудование
● Промышленное управление
● Оборудование безопасности
● Высокоскоростные контрольно-измерительные приборы
Абсолютные максимальные номинальные значения (температура окружающей среды: 25 °C)\
| Item | symbol | value | units | Note | |
| Input | Continuous LED Current | IF | 50 | mA | |
| Peak LED Current | IFP | 1000 | mA | f= 100Hz , duty- 1% | |
| LED Reverse Voltage | VR | 5 | V | ||
| Input Power Dissipation | PIN | 75 | mW | ||
| Output | Load Voltage | VL | 60 | V(AC Peak or DC) | |
| Load Current | IL | 500 | mA | ||
| Peak Load Current | Ipeak | 1.5 | A | 100ms(1 pulse) | |
| Output Power Dissipation | Pout | 450 | mW | ||
| Total power Dissipation | PT | 500 | mW | ||
| I/o Breakdown voltage | VI/O | 1 500 | Vrms | RH=60% , 1 min | |
| Operating Temperature | Topr | -40 to +85 | ℃ | ||
| Storage Temperature | Tstg | -40 to +100 | ℃ | ||
| Pin soldering Temperature | Tsol | 260 | ℃ | 10 sec max. | |
Электрические характеристики (температура окружающей среды: 25 °C)
| Item | Symbol | MIN. | TYP. | MAX. | Units | Conditions | |
| Input | LED Forward Voltage | VF | 1.2 | 1.4 | V | IF=10mA | |
| Operation LED Current | IF on | 0.5 | 3.0 | mA | |||
| Recovery LED Current | IF off | 0.35 | 0.5 | mA | |||
| Recovery LED Voltage | VF off | 0.5 | V | ||||
| Output | On-Resistance | Ron | 20 | 30 | Ω | IF=5mA,IL=100mA,Time to flow is within 1 sec. | |
| Off-State Leakage Current | ILeak | 1 | uA | VL=Rating | |||
| Output Capacitance | Cout | 110 | pF | VL=0, f=1MHz | |||
| Transmis sion | Turn-On Time | Ton | 0.23 | 0.5 | ms | IF=5mA, IL=100mA, | |
| Turn-Off Time | Toff | 0.05 | 0.2 | ms | |||
| Coupled | I/O Isolation Resistance | RI/O | 1010 | Ω | DC500V | ||
| I/O Capacitance | CI/O | 0.8 | 1.5 | pF | f=1MHz | ||
Справочные данные.
Размеры.
Габаритные размеры.
Информация о заказе.
| Category | Output rating*1 | Part No. | Packing quantity | |
| Load voltage | Load current | SOP | Tape and reel | |
| AC/DC | 400 V | 0.1A | FTY 210 | 1-reel: 1,000 pcs. |
Важное уведомление:
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they are applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or other. Further details are available from any F-tone Networks sales representative.
Power and Wavelength Testing
Test the signal delivering strength and wavelength, to ensure the signal decoding capacity of the receiver, and the wavelength remains consistent from the transmitter to the receiver.
Traffic Testing
Test the bit error rate and packet loss rate, to make them meet the corresponding standards and ensure the performance of transceivers.
Optical Performance Testing
Test the transceivers’ eye diagram situation, receiving sensitivity, extinction ratio, wavelength, light-emitting, light-receiving, current and voltage, to ensure the signal quality, stability and reliability of the transmission.
End Face Testing
Check the end face of the transceivers and keep them clean for more stable data transmission, better performance, and durability.
